Virtually Perfect Replica Casting of Internal and External Forms
Excellent For Checking Parts With Optical Comparators
Non-Toxic & Easy To Use
No Release Agent is Ever Needed
100 Times Faster Than RTV Silicones
Supplied in Two Viscosities
THIN POUR
Final Color:LIGHT GREEN
For internal-shape applications where a thin pour will completely
fill the cavity without voids. A complete replica casting is quickly formed.
Manipulation time is 5 minutes and cure time is 15 minutes.
Start to finish: 20 minutes.
Kits include graduated mixing cups, wooden spatulas
and instructions.
Use with REPRO-MIX Dispensing Gun System
NEW Trial Size Kit Now Available #16116
- Thin Pour 130ml Trial Kit Standard Size Kits #16135
- Thin Pour 380ml Kit #16137
- Case of 10 380ml Kits
QUICKSETTING PUTTY
Final Color:LIGHT BLUE
Roll two equal-sized balls of catalyst putty and base putty and
simply knead them together like dough.
Excellent for external shapes. Simply spread over master pushing down with fingers
and wait for cure 8-10 minutes. You have 3 or 4 minutes
of manipulation time - Therefore 14 minutes start to finish. You can also cast internal shapes and cavities but some pressure
should be applied such as a weighted object on top.
New Trial Size Kit Now Available #16129
- 220ml Trial Quick Set Putty Kit Other Kits: #16130
- 13/4 lb. (520ml) Introductory Kit #16131
- 7 lb. (2150ml) Economy Kit
Physical Properties and Applications
REPRORUBBER
THIN POUR
REPRORUBBER QUICK SETTING PUTTY
Mix Time (Stirring in a cup)
30 - 45 seconds
30 - 45 seconds
Working Time (Manipulation Time)
4 minutes
2 minutes (from beginning of mix)
Setting Time (at room temperature)
10 - 15 minutes
6 minutes
Permanent Deformation
0.2%
0.3%
Dimensional Stability
less than 0.50%
less than -0.25%
Tear Strength
44 pounds per sq. inch
105 pounds per sq. inch
Elongation
60% at break
6.3% at break
Durometer (Shore A-2)
30 (at 15 minutes)
50(at 7 minutes)
Temperature Stability
1 week @ 60oC
1 week @ 60oC
Detail Reproduction
EXCELLENT
EXCELLENT
Applications:
You can take impressions of:
ALL METALS
ALL PLASTICS
NON METALS
RUBBER
PAPER OR CARDBOARD ITEMS
CERAMIC AND GLASS ITEMS
WOOD, MARBLE, ETC.
Other Uses Include:
Fixturing where semi-rigid structure is desired.
Making joints where flexibility is required.
Prototypes of rubber type components such as gaskets, washers, etc.
As a mask for high temperature plasma spray of metallic coatings.
Physical Advantages Over the Hard-Copy Replicas:
Replica is easy to remove - even if there are under cuts or
grooves.
Cross-sectioning of replica is easily accomplished with a
knife or razor.
It can then be checked on an optical comparator or microscope.
Surface finish replication is exact with excellent optical properties.
Replicas are permanent - will not leach or ooze out nor outgas.
NO MORE 16 HOUR CURE TIME AS WITH RTV SILICONES
MORE ACURATE THAN ALL OTHER RTV COMPOUNDS
REPRORUBBER PUTTY will withstand up to 600oF (or more).
Reprorubber copies can be recopied (copy from a “female mould” yields a male-shaped replica). See EPOXY PARFILM ULTRA.
For Reprorubber® Thin Pour Users REPRO-MIX™ DISPENSING GUN SYSTEM
A “Ready-To-Fill” Mixing and Dispensing System that Enables You to Make Quick
and Accurate Reprorubber Replicas...Without Manual Mixing and Fuss!
REPRO-MIX™ SYSTEM CONSISTS OF THE FOLLOWING:
50ml dual barrel syringe with reusable end cap; easily filled by pouring contents of Reprorubber into cartridge barrels.
Disposable low cost Helix Mixing Nozzle Tips easily attach to and detach from dual barrel syringe.
REPRO-MIX Dispensing Gun.
#16132
-Complete REPRO-MIX™ Kit consisting of 1 each
REPRO-MIX™ Dispensing Gun, 10 each 50ml, Dual
Barrel Cartridges, 20 each Helix Mixing Nozzle
Tips, Caps, Plugs and complete instructions for
usage #16133
- Dual Cartridge Replacement Pac (10 each including
caps and plugs) #16134
- Helix Mixing Nozzle Tip Pac (20 each)
Inspection Measurement 
